Laser cutting thickness chart.
Maximum thickness by material, plus kerf, minimum hole size and edge quality, from the shop floor of a working laser cutter in Ahmedabad.
Short answer: a 3 kW CO₂ laser cuts mild steel up to 20 mm, stainless steel up to 12 mm, aluminium up to 8 mm, GI up to 8 mm, brass up to 6 mm and copper up to 3 mm. Edge quality is best in the thinner half of each range; near the maximum, cuts are slower and edges rougher.
| Material | Max thickness (3 kW CO₂) | Best quality range | Assist gas | Min. hole Ø |
|---|---|---|---|---|
| Mild steel (IS 2062, CRCA, HR) | 20 mm | 0.8–12 mm | Oxygen | ≈ thickness |
| Stainless steel 304 | 12 mm | 0.5–6 mm | Nitrogen | ≈ thickness |
| Stainless steel 316 | 10 mm | 0.5–6 mm | Nitrogen | ≈ thickness |
| Aluminium (5052, 6061) | 8 mm | 0.8–4 mm | Nitrogen | ≥ thickness |
| Galvanised (GI) | 8 mm | 0.5–3 mm | Nitrogen / air | ≈ thickness |
| Pre-painted sheet | 4 mm | 0.5–2 mm | Nitrogen | ≈ thickness |
| Brass | 6 mm | 0.5–3 mm | Nitrogen | ≥ thickness |
| Copper | 3 mm | 0.5–2 mm | Oxygen / nitrogen | ≥ thickness |
Why thickness limits differ by material
Mild steel is cut with oxygen, which reacts with the hot iron and adds energy to the cut, so thick MS cuts well. Stainless and aluminium are cut with nitrogen, which only blows molten metal out, so all the energy comes from the laser and the practical limit is lower. Brass and copper reflect much of the laser beam and conduct heat away quickly, so they have the lowest limits.
Kerf and tolerance
| Thickness | Typical kerf | Typical part tolerance |
|---|---|---|
| Up to 3 mm | 0.15–0.25 mm | ±0.1 mm |
| 3–8 mm | 0.25–0.4 mm | ±0.1–0.15 mm |
| 8–20 mm | 0.4–0.6 mm | ±0.2–0.3 mm |
Thicker than the chart?
For MS above 20 mm, plasma or oxy-fuel cutting is usually cheaper; see laser vs plasma cutting. For thicker stainless, consider waterjet. And if you're unsure which gauge to choose, the sheet metal gauge chart converts gauge to mm.
Questions buyers ask us.
How thick can a laser cut steel?
It depends on laser power and type. A 3 kW CO₂ laser such as the TRUMPF TruLaser 3030 cuts mild steel up to about 20 mm and stainless steel up to 12 mm. High-power fiber lasers (12 kW and above) can cut MS beyond 30 mm.
What is the kerf width in laser cutting?
Kerf (the width of material removed) is typically about 0.15 to 0.3 mm on thin sheet and widens to roughly 0.4 to 0.6 mm on thick plate. CAM software compensates for it automatically, so you draw parts at their true size.
What is the smallest hole that can be laser cut?
As a rule, a hole diameter at least equal to the sheet thickness cuts cleanly. In thin sheet, holes down to about 0.5 to 1 mm are possible; in thick MS plate, keep holes at or above the plate thickness.
Send the drawing. Get the price.
DXF, DWG, STEP or a PDF sketch. An engineer checks it and replies on WhatsApp or email during working hours.